SUNAURA MACHINERY BLOG

SunAura Commissions a Counter-Pressure Beer Can Filling and Seaming Line for a Craft Brewery in Chile

Counter-pressure beer can filling line
Beer looks like a simple liquid to fill, but its dissolved CO₂, foam sensitivity and sub-20-ppb O₂ pickup limit change the equipment choice. A water or soft-drink can filler would over-oxygenate the beer in the first hour.

SunAura Machinery has commissioned a counter-pressure can filling and seaming line for a craft brewery in the Santiago valley, Chile. The brewery cans 330 ml and 500 ml Lagers, IPAs and stouts at 60–80 cans/min, distributing to restaurants and retail across Chile and Peru. The project replaced a small manual gravity filler that oxygenated the beer, produced variable fills, and could not keep up with summer demand.

A standard soft-drink can filler would have failed here on three points: it would over-oxygenate the beer, it would not hold counter-pressure during filling, and it would foam over on IPAs with high hop bitterness. This line was specified around beer reality.

Why Counter-Pressure — Not Gravity or Overflow

Beer holds dissolved CO₂. When you open a can or bottle, the CO₂ comes out of solution as foam. A gravity filler pours beer at atmospheric pressure, which makes the beer foam and pulls oxygen in. A counter-pressure filler first pressurises the can with CO₂ to match the tank pressure, then fills beer from the bottom up without degassing. That is why O₂ pickup stays under 50 ppb and the beer holds its shelf life.

Filler typeO₂ pickupBeer suitabilityWhy
Gravity / overflow200–500+ ppbNot suitableFoams over, oxygenates, flat in weeks
Isobaric / counter-pressure (this line)Under 50 ppbSelectedCO₂ pre-pressurise, bottom-up fill, no degassing
Hot-fill / asepticLowNot suitableKills live yeast and off-flavours in craft beer

Two Beer-Specific Details That Decide Quality

Bottom-up fill with foam purge. The filling valve reaches the can bottom and fills upward; when the beer reaches the can shoulder, a small head of foam (not air) pushes out the headspace before seaming. This is why the beer does not taste “wet” or “cardboard” after two months on a shelf.

Can rinsing and CO₂ purge before fill. Dust and air in the can are the largest source of O₂ pickup. The line includes a pre-rinse with sterile water and a CO₂ purge before the counter-pressure cycle. Skipping this step is the most common mistake craft breweries make when upsizing from a manual filler.

Integrated packaging line
Craft breweries move from a 20-cans/min manual bench to a 60–120-cans/min line. The deciding factor is not top speed but O₂ control, can changeover between 330 and 500 ml, and whether the seamer logs torque for QA.

Who This Line Suits — and What We Would Specify Differently

This configuration targets craft breweries and contract brewers at 60–120 cans/min running 330 ml and 500 ml cans of still or CO₂-carbonated beer, where O₂ pickup and foam control matter. Breweries below 30 cans/min are better served by a semi-automatic counter-pressure bench; breweries above 300 cans/min step to a rotary isobaric platform. For sparkling wine or cold brew coffee with lower carbonation, the counter-pressure logic still applies but the pressure set-point changes.

The line passed FAT at our Qingdao workshop with the customer’s actual beer, checked O₂ pickup and fill weight across a full run, and shipped with spare filling valves, seamer chucks and commissioning support covered under our after-sales service terms. For more on filling principles, see liquid filling machines.

Canning or bottling carbonated drinks and worried about O₂ pickup and foam? Send your product, cans/min and carbonation level to [email protected] or on WhatsApp. We will tell you whether counter-pressure filling is worth it for your speed and product. Browse our integrated lines and other commissioning news.

We use cookies to improve your experience on our website, analyze traffic, and personalize content. By browsing this website, you agree to our use of cookies. Learn more