
High-Level Layer Palletizer
A Layer palletizer sized by the case weight, the pattern and the rate the line actually produces.
| Output | see specification |
|---|---|
| Configuration | Single station |
| Accuracy | per specification |
| Price band (FOB) | US$ 6,000 – 30,000 |
| Lead time | 25 – 45 days |
1. Who this machine is for, and who should not buy it
This machine is bought by plants that have reached the point where two or three people per shift are stacking cases by hand, or where the case weight has passed the level a person should lift repeatedly. The decision is about labour, injury risk and pattern consistency, not about speed.
It is the wrong choice when the line runs fewer than about 15 cases per minute, when the case range changes every few days with no pattern standardisation, or when the floor space cannot take the machine plus the pallet positions plus the safety zone. In those cases manual palletizing is genuinely cheaper.
The realistic buyer runs 15 to 60 cases per minute, has two to six case sizes, uses standard pallets, and needs a pattern that stays square through wrapping and shipping.
2. How it works
Cases arrive on an infeed conveyor, are oriented by a turning section or a pattern-forming station, and are picked by the robot or the layer head and placed on the pallet in a programmed pattern. Full layers are built on a layer table and pushed onto the pallet as one unit, which is faster than placing every case individually.
The pattern is the core of the engineering. A pattern that interlocks and stays square stacks higher and wraps better; a pattern that leaves a chimney in the middle collapses in transit. Good palletizing is designed around the case dimensions, not around the robot.
Cycle time is the constraint: pick-and-place, layer build and pallet exchange all consume seconds. A robot rated at 12 cycles per minute does not place 12 cases if each pick is two cases, and the quotation should be read in cases per minute, not cycles.
3. Configuration matrix: what changes and what it costs you
The same base frame is sold in several configurations, and the differences matter more than the marketing names suggest. The table below maps each configuration to the buyer profile it actually fits, so you can rule out options before they appear in a quotation.
| Configuration | Heads | Typical output | Container range | Best for | Trade-off |
|---|---|---|---|---|---|
| 4-axis robot | 1 robot | 15 – 30 cases/min | Case 5 – 50 kg | Compact lines | Fixed pattern, no complex shapes |
| 6-axis / articulated | 1 robot | 20 – 40 cases/min | Case 5 – 120 kg | Flexible patterns | Higher price, larger footprint |
| Layer palletizer | layer head | 30 – 60 cases/min | Case 5 – 25 kg | High volume single product | Pattern change needs a new head |
| Gantry | 1 head | 15 – 35 cases/min | Bag or case | Wide lines, long reach | Floor space under the gantry |
| Dual station | 1 – 2 robots | 30 – 50 cases/min | Case 5 – 50 kg | Two lines into one palletizer | More changeover complexity |
| Collaborative | cobot | 8 – 15 cases/min | Case up to 15 kg | Small cells, shared space | Lower speed, no fence |
The layer head is the fast answer and the inflexible one. A robot is the flexible answer and slower per case. Buyers who change patterns weekly should not buy a layer head, and buyers who run one pattern for years should not pay for a robot.
4. Technical specifications
Figures below are the standard build. Every value can be changed, but each change moves price, lead time and the commissioning effort, so read the notes column before asking for a variant.
| Parameter | Standard | Optional / range | Why it matters |
|---|---|---|---|
| Type | Layer palletizer | Layer palletizer | Fixed at order |
| Rate | 15 – 60 cases/min | Per layout | Quote in cases, not cycles |
| Payload | 50 kg standard | 120 kg / 180 kg heavy | Case plus gripper weight |
| Reach | 2.0 – 3.1 m | Per robot model | Determines the layout |
| Pallet size | 1,000 × 1,200 mm | 1,200 × 1,200 mm | Standard or custom |
| Stack height | Up to 2,000 mm | Up to 2,400 mm | Check ceiling and fork height |
| Patterns | Recipe per SKU | Up to 50 recipes | More than 50 slows changeover |
| Gripper | Vacuum clamp | Clamp + vacuum for mixed cases | Gripper is product-specific |
| Safety | Fence + light curtain | Safety scanner for cobot | CE requires risk assessment |
| Control | PLC + HMI | Pattern editor | Pattern editing matters |
| Air | 0.6 MPa, 0.3 m³/min | Higher for vacuum | Compressor sizing |
| Power | 5 – 12 kW | Up to 18 kW heavy duty | 380 V three-phase |
5. Throughput and capacity planning
Real output is cases per minute including pattern changes and pallet exchanges, not robot cycles. A pallet exchange costs 20 to 40 seconds, so a line running 40 cases per minute loses about 8 % of its capacity to exchanges alone.
Plan on 80 % of the quoted rate. The losses come from infeed gaps, rejected cases, pattern change, pallet exchange and the stops when the stretch wrapper is not ready.
If the palletizer is the last machine before wrapping, its buffer is the pallet position. One position is not a buffer; two positions let the wrapper finish while the palletizer builds the next pallet, and that is usually worth more than a faster robot.
| Shift pattern | Gross output | OEE at 65% | Annual bottles (300 days) |
|---|---|---|---|
| 1 × 8 h | 60 bph | 39 bph | 93,600 |
| 2 × 8 h | 60 bph | 39 bph | 187,200 |
| 3 × 8 h | 60 bph | 39 bph | 280,800 |
Size the machine on the middle of the range, not the top. A unit sold at 60 bottles per hour that runs at 60 for six hours a day is being asked to live at its mechanical limit; the same unit at 45 bottles per hour has headroom for viscosity drift, cap changes and the occasional slow batch.
6. Product and container fit
Fit is decided by case range and pattern. A plant with six case sizes and no standard pattern will spend more time changing recipes than palletizing, and the answer there is to standardise the cases before buying the robot.
Case integrity matters too. A case that is not square, or that has a bulging bag inside, cannot be stacked to 2 m without collapsing. The palletizer does not fix a weak case; it exposes it.
| Product type | Viscosity band | Fit | What to watch |
|---|---|---|---|
| Regular slotted cases | square, rigid | Excellent | Most common application |
| Bags and sacks | soft, shifting | Good with bag head | Shape stability is the limit |
| Trays and shrink packs | flat, light | Good with vacuum gripper | Vacuum needs a sealed surface |
| Pails and drums | round, heavy | Good with clamp | Heavy payload, low rate |
| Mixed SKU pallets | varies | Conditional | Store-level mixing slows the robot |
| Damaged or bulging cases | irregular | Not suitable | Stack collapses in transit |
7. Selection decision framework
Use these rules in order. Each one is a hard filter, not a preference, and each is written so that two buyers with different constraints reach different answers rather than the same recommendation.
Rule 1: Rate in cases first
Convert every quotation to cases per minute including exchanges. A robot quoted at 12 cycles is 12 cases only if the gripper picks one case.
Rule 2: Pattern second
The pattern decides stack stability and trailer fill. Ask for the pattern drawing with the pallet footprint and layer count before the order, not after.
Rule 3: Payload third
Case weight plus gripper weight must sit below the rated payload with 20 % margin. A 50 kg payload robot lifting a 50 kg case is a robot running at its limit every cycle.
Rule 4: Pallet positions fourth
Two positions is the minimum for a continuous line. One position means the line stops while the pallet is exchanged.
Rule 5: Safety fifth
Fenced cells need light curtains at the infeed and a risk assessment for CE. A cobot removes the fence and adds a speed limit, which is a trade, not an upgrade.
Rule 6: Floor and ceiling sixth
Check the stack height plus the gripper plus the robot arm against the ceiling, and check the floor for point loading. Retrofitting a taller stack height means a new robot.
8. Alternatives compared head to head
Palletizing competes with manual stacking, with a layer palletizer and with a dedicated inline machine, and the choice is decided by rate and pattern stability.
| Criterion | High-Level Layer Palletizer | Robotic palletizer | Layer palletizer | Manual palletizing |
|---|---|---|---|---|
| Rate | 15 – 40 cases/min | 30 – 60 cases/min | 10 – 20 cases/min | see specification |
| Flexibility | High, recipe per SKU | Low, head per pattern | Total | see specification |
| Labour | None in run | None in run | 2 – 3 per shift | see specification |
| Footprint | Medium | Large | None | see specification |
| Price | US$ 45,000 – 120,000 | US$ 80,000 – 180,000 | None | see specification |
| Best fit | Multiple sizes, medium rate | One pattern, high rate | Low rate, low wage | see specification |
Manual palletizing is not irrational: at 12 cases per minute with a low wage and light cases, it is often cheaper than any machine for years. The calculation changes when cases exceed 20 kg or the injury record becomes a cost.
9. Line integration
The palletizer sits at the end of the case line, before the stretch wrapper. Upstream it needs a case stream with consistent orientation and a defined gap; downstream it needs at least one buffered pallet position so the wrapper can run while the next pallet is built.
The infeed orientation device is part of the palletizer specification, not an accessory. A palletizer fed with randomly rotated cases places badly and stops often, and the pattern that results is not the one on the drawing.
Signals worth agreeing: case-present, pallet-ready, pattern-complete, fault and a pallet-full output to the wrapper. Without a pallet-ready interlock, a pallet can be exchanged while the robot is placing, which is a crash rather than a stop.
10. Hygiene, materials and compliance
In food rooms the gripper and the case contact surfaces need stainless or food-grade materials, and the frame needs to be cleanable underneath. Robots are notoriously good at collecting dust in the joints, so specify a clean-room or washdown variant where the room demands it.
Documentation covers the risk assessment, the guard drawing and the gripper material certificates. Auditors ask for the risk assessment before they ask for anything else on an automated cell.
If the line runs frozen or wet product, specify a stainless gripper and IP65 motors at order. Retrofitting a gripper is a mechanical rebuild.
11. Installation and commissioning
| Stage | Duration | Who does it | Deliverable |
|---|
Installation and commissioning take five to eight days, and the pattern programming is the slow part. Bring two or three real cases of each size to commissioning; pattern work with dummy cases produces a pattern that fails on the real product.
12. Maintenance, spares and uptime
The robot itself needs little: grease, belt inspection and a backup battery for the controller. The gripper, the infeed orientation and the pallet conveyor take most of the maintenance attention.
Keep one gripper seal kit, a set of vacuum pads and a spare photo-eye. These are the parts that stop the cell, and they are cheap compared with a stopped line.
| Wear part | Interval | Cost band | Downtime if ignored |
|---|---|---|---|
| Vacuum pads | 6 – 12 months | US$ 15 – 60 each | Case slip, dropped cases |
| Gripper seals | 12 months | US$ 40 – 120 per set | Loss of vacuum |
| Controller battery | 24 – 36 months | US$ 30 – 80 | Pattern loss after power cut |
| Pallet conveyor chain | 24 months | US$ 200 – 600 | Pallet drift, positioning error |
13. Cost structure and total cost of ownership
The five-year cost is dominated by the labour it replaces and the cases it damages. A robot that drops one case per thousand saves labour and creates a rework cost that rarely appears in the payback calculation.
Build the case for the investment on loaded labour cost per shift plus the injury record, then compare with the machine plus its maintenance and gripper consumables. The payback usually lands between 18 and 30 months at two operators per shift.
| Cost line | Typical band | Notes |
|---|---|---|
| Machine, FOB | US$ 45,000 – 120,000 | Payload and gripper |
| Pallet conveyor and positions | US$ 8,000 – 20,000 | Two positions minimum |
| Safety and guarding | US$ 3,000 – 8,000 | Risk assessment included |
| Power | US$ 0.8 – 2.0 per hour | Robot duty cycle |
| Spares, year 1 | US$ 600 – 1,800 | Pads, seals, sensors |
| Install and pattern work | US$ 2,000 – 5,000 | Five to eight days |
14. RFQ checklist
A quotation is only as precise as the inputs behind it. Buyers who send these fourteen data points in the first email typically receive a firm price and a layout drawing on the first reply; buyers who send “a filling machine, about 5,000 an hour” spend three rounds establishing what that means.
15. Quality assurance and FAT documentation
Factory acceptance runs the cell with sample cases at the quoted rate for at least 30 minutes and checks the pattern, the stack squareness and the pallet exchange time. The report records the rate achieved in cases per minute and the exchange time in seconds.
Ask for a video of the pattern being built, including the top layer. The top layer is where an unstable pattern shows itself, and it is the layer that decides whether the pallet survives the truck.
16. Frequently asked questions
How many cases per minute can it do?
Between 15 and 60 depending on the head and the pattern. The number to compare is cases per minute including pallet exchange, not robot cycles.
Can it handle several case sizes?
Yes, with a recipe per size. Above about 20 recipes the changeover time becomes the limit, and standardising cases is the better investment.
Do I need two pallet positions?
For a continuous line, yes. One position means the line stops for every exchange, which costs about 30 seconds each time.
What payload should I specify?
Case weight plus gripper weight with 20 % margin. Running a robot at its rated payload every cycle shortens its life.
Can a cobot replace a fenced cell?
It can, at a lower rate and a lower payload. It removes the fence and adds a speed limit; it is a trade for space, not a free upgrade.
How long is commissioning?
Five to eight days including pattern programming. Bring real cases for each size.
17. Footprint, utilities and infrastructure
Site planning fails more often on ceiling height and drain position than on floor area, so check these three numbers before the layout is drawn: the height needed for nozzle lift plus the tallest container, the distance from the machine to the nearest drain, and the free capacity on your compressed-air ring main at shift start, when every other machine is also drawing air.
| Item | Requirement | Note |
|---|---|---|
| Floor area | 2.4 x 1.3 m for the machine, plus 1.2 m service access on each side | Access is for the mechanic, not for the operator |
| Ceiling height | 1.9 m minimum above the frame | Nozzle lift plus container height |
| Power | 3 kW, 380 V three-phase, 50 or 60 Hz | Separate circuit with earth, not shared with welders |
| Compressed air | 0.6 MPa, 0.4 m3/min free capacity | Dry air; moisture causes valve sticking |
| Drain | Within 1.5 m of the machine | For washdown and for the drip tray outlet |
| Noise | Under 75 dB(A) at 1 m | Most of it comes from the vacuum pump or blower, not the filler |
A common mistake is to install the machine against a wall to save floor space. The service access on the left side is where the mechanic reaches the drive and the valve manifold; blocking it turns a fifteen-minute job into a two-hour dismantling job, and in practice it also means the machine is never serviced properly.
18. Application scenarios by industry
The same machine is bought for very different reasons, and the configuration that suits one industry is often wrong for another. These four patterns cover most of the enquiries we receive, and each one points to a different set of options.
Food and beverage producers usually need washdown-capable surfaces, food-contact declarations and a changeover fast enough to run three products in a shift. Their decision is driven by the retailer audit, and the machine is specified with stainless frame, IP65 electrics and removable nozzles. Their biggest hidden cost is not the machine but the changeover labour they did not plan for.
Cosmetic and personal-care producers fill smaller volumes at lower output, and their constraint is appearance: no drips on the bottle shoulder, no product in the thread, consistent fill line across a batch. They need a back-suction or suck-back nozzle and a slower final approach more than they need speed, and they usually regret buying a machine sized for output rather than for cleanliness.
Pharmaceutical and diagnostic producers buy documentation as much as hardware. The filling head is secondary to the material traceability, the validation package and the ability to prove that cleaning was effective. Their machine is 316L, their seals are PTFE, and their acceptance test is a written protocol rather than a visual check.
Chemical and household producers fill corrosive or volatile liquids where the wetted material and the seal elastomer decide the machine life. They need Viton or PTFE seals, a stainless frame, and often an extraction hood over the filling zone. Accuracy is less critical than containment, and the machine should be specified accordingly.
19. Supplier evaluation: seven questions with answers you should accept
Buying a filling machine is a comparison between suppliers as much as between machines, and the difference shows up in the second year rather than the first. These seven questions are the ones that separate a supplier who builds machines from one who resells them, and each has an answer you can check against a document.
1. Can you show the calibration record for every head?
A serious supplier weighs thirty bottles per head and reports mean and standard deviation per head, not a single number for the machine. If a head is 2 % off while the average looks fine, the record exposes it and the machine should not ship.
2. What is the spare-part lead time for wear items?
Nozzle seals and valve seats should be shippable in under a week from stock. If the answer is “we order from the OEM”, your machine stops for two weeks the first time a seal fails, and seals always fail.
3. Who signs the acceptance test, and against what criteria?
The criteria should be written before the order, in numbers: output over four hours, volume tolerance, drip count, reject rate. A supplier who will not commit to numbers is telling you the numbers are not stable.
4. What is the changeover procedure, and who can perform it?
An operator should be able to change format in under ten minutes with a recipe call and one tool. If the answer involves a mechanic and a spanner, add the labour cost to your five-year total before you compare prices.
5. Which parts are bought in, and from where?
Servo drives, PLCs, pneumatic valves and load cells are branded components, and their availability in your region decides whether a breakdown is a two-day or a two-month event. Ask for the brand list and check local distribution before you sign.
6. What does commissioning include, and what costs extra?
Installation, calibration, training and a production trial should be itemised. The expensive surprises are usually crane hire, extra engineers beyond the agreed days, and re-commissioning after your utilities turn out to be out of specification.
7. Can we speak to a customer running the same product?
A supplier with a real installed base can name two or three references on request. Vague answers here are the single strongest signal to slow down.
20. The first 90 days after arrival
The first three months decide whether the machine settles into a rhythm or becomes a source of daily firefighting. Most of what goes wrong in this window is procedural rather than mechanical, and it is fixable if it is watched.
Days 1 to 10: install, level and align to the conveyor, verify rotation direction and air pressure, then run empty containers through every station by hand before powering the filling circuit. Record the as-built settings in the manual rather than on a note taped to the frame.
Days 11 to 30: calibrate each head on your own product at your own filling temperature, then run a full shift at 70 % of rated output and log volume every hour. The drift pattern in this shift predicts the maintenance interval better than any manual.
Days 31 to 60: train a second operator and one mechanic, not just the person who will run the day shift. Single-person knowledge is the most common cause of a line that cannot run at weekends or during holidays.
Days 61 to 90: review the reject log, count the stops and their causes, and set the first preventive-maintenance dates from the real failure pattern rather than the generic intervals in the manual. Order the first spare kit before the end of this window, because the first seal failure usually arrives around month four.
21. Specification mistakes that cost buyers money later
Nearly every unhappy installation traces back to a decision made in the quotation stage, when a number was accepted without being checked. These six mistakes appear often enough to be predictable, and each is cheap to avoid at order and expensive to correct after arrival.
Accepting output quoted without container details
A speed quoted in bottles per hour means nothing until it is tied to a fill volume, a neck diameter and a product viscosity. Ask for the test conditions in writing: 500 ml, 28 mm neck, water at 20 °C is a very different machine from 1 L, 18 mm neck, syrup at 12 °C.
Buying the maximum head count the budget allows
More heads raise output, but they also raise air consumption, spill risk, calibration work and the cost of every future seal replacement. A machine with eight heads running six days a week at 80 % utilisation beats a twelve-head machine running three days at 45 %.
Forgetting the conveyor pitch
The filling machine, the capper and the labeller must share a container pitch and a conveyor height. When they do not, the integrator builds a transfer plate and a pitch change, and the buyer pays for it in commissioning time and in jams that never quite disappear.
Under-specifying the electricals
IP65 electrics, a separate earth and a dedicated circuit cost a few hundred dollars at order. Retrofitting them into a running line costs a shutdown, a new cabinet and an electrician, and until it is done the machine is a washdown hazard.
Buying seals by price
A seal that costs two dollars less and lasts half as long doubles your maintenance labour and adds a failure mode in the middle of a production run. Specify the elastomer by product compatibility, not by unit cost.
Treating training as a formality
Two days of training with written SOPs is the cheapest reliability investment available. Buyers who skip it usually spend the same money later on a service visit to fix problems the manual already described.
22. Comparing quotations line by line
Three quotations for the same nominal machine can differ by 40 % and still describe the same hardware, because what sits inside the price is different. The line-by-line comparison below is the one we recommend to buyers, and it is also the format our own proposals follow so that the differences are visible rather than buried in a total.
What should be inside the base price
The base price should include the machine as specified, one set of tooling for the agreed format, the control system with its recipe memory, guards and interlocks, an English manual, a tool kit and a spare seal set. If any of those appear as separate lines in a competing quotation, the totals are not comparable and the cheaper number is usually the one with more excluded.
What should be quoted separately, and why
Freight, insurance, duties, installation, training beyond the included days, custom tooling and optional inspection equipment should be separate. That is not a trick; it lets you see the cost of each decision. The trick is the opposite: a single lump sum that hides a two-week commissioning visit inside a number you cannot audit.
Warranty terms
Compare the duration, what is covered, who pays the freight on a warranty part, and what voids the warranty. Twelve months on parts with buyer-paid freight is very different from twelve months including freight and labour. Ask for the wording, not the summary.
Payment schedule and risk
Thirty per cent deposit and seventy per cent against documents is the common structure for export. A supplier asking for the full amount before dispatch is asking you to carry all the risk; a supplier accepting ten per cent deposit is carrying it themselves. The schedule tells you something about who expects to have problems.
Lead time and its components
Ask for the split between engineering, procurement, assembly, testing and packing. A lead time of forty days that is thirty days of waiting for a servo drive is a different risk from forty days of assembly. When a date slips, the split tells you whether to push the supplier or the component.
23. Questions procurement teams ask us most often
Can you supply the same machine on 415 V, 60 Hz?
Yes. Voltage, phase and frequency are specified at order because they change the motors, the drives and the transformer sizing. Changing them after the machine is built means replacing components, and it is one of the few specifications that cannot be adjusted on site.
What is the actual delivery time to our port?
Production lead time is 25 to 45 days, sea freight to most destinations is 18 to 35 days, and port-to-door adds three to ten days depending on customs. The total is what your planning needs, and it is usually 8 to 12 weeks from order to a machine running in your plant.
Do you provide a local installation service?
We send engineers from the factory for installation and commissioning, and for repeat buyers we can arrange a local partner for routine service. Installation by the factory team is the option we recommend for a first machine, because it transfers the process knowledge as well as the hardware.
What happens if a part fails in the first year?
Warranty parts ship by air within three working days of a confirmed diagnosis, and we ask for photographs and the fault code so the diagnosis is right the first time. For critical wear items we recommend holding a local kit, which costs a few hundred dollars and removes the air-freight delay entirely.
Can the machine be audited before we release the balance?
Yes. The factory acceptance test is the natural point: you or your third-party inspector attend, watch the run, review the calibration data and the material certificates, and the balance is released against a signed report. Buyers who skip this step sometimes discover a specification mismatch only after the container arrives.
24. Service levels, response times and what we commit to in writing
Service is the part of a machine purchase that buyers cannot inspect before they pay, which is exactly why it deserves a place in the comparison spreadsheet. What follows is what we put in the contract rather than what we say in a sales meeting, and we recommend asking every competing supplier the same four questions.
Response time
First technical response within one working day of a written query with photographs and the fault code. Remote diagnosis within two days. Where a site visit is needed, an engineer is dispatched within five working days, or sooner if the line is stopped.
Spare parts
Wear items from stock, shipped within three working days by air. Non-stock parts are quoted with a lead time in writing. The recommended spare kit is listed in the manual with part numbers, so you can reorder from any distributor rather than only from us.
Warranty
Twelve months on parts and labour for defects in manufacture, twenty-four months on the frame. Consumables and wear items are excluded, which is normal, but the exclusion list is written down rather than implied. Warranty freight is covered by us for the first shipment of a replacement part.
Training and knowledge transfer
Two days of on-site training are included with commissioning: one day for operators covering start-up, changeover, cleaning and the first line of fault finding, and one day for the mechanic covering adjustment, wear inspection and the spare-parts replacement procedure. Both days end with a written SOP that your team keeps.
What we do not promise
We do not promise a response time measured in hours, because a promise that cannot be kept is worse than a realistic one. We do not promise that a machine will run at its maximum output indefinitely; we promise the tested output on the format and product used at acceptance, and we document the conditions. Buyers who want a guarantee on through-life output should buy a service contract, and we quote those separately so the cost is visible.
27. Handover, acceptance and what to verify on site
Acceptance should be a rate test and a pattern test, both recorded. Run the cell for thirty minutes at the quoted rate, count the cases placed, note every stop and its cause, and photograph the finished pallet from four sides including the top layer.
On site, verify the sequence interlocks before production: that the robot cannot release a case without a pallet present, that the pallet conveyor cannot move during a place cycle, and that the light curtain stops both motion and the infeed. These three checks are the ones an auditor will ask about.
Take a copy of the controller backup and the pattern files at handover. Pattern data is the part of the machine that is hardest to recreate, and a controller battery failure without a backup costs a week of reprogramming.
Send your container and product details
Send the case dimensions and weights, the pallet size, the pattern you use today and the line rate. We will confirm the robot payload, the gripper and the pallet positions, and send a priced layout with a pattern drawing and a rate test protocol.
